袋除尘器工作原理及结构特点 - 诺和环保设备

     我司生产的玻纤袋式除尘器是专为水泥立窑和烘干机废气除尘开发的_设备，该设备采用微机控制，分室反吹，定时、定阻清灰，温度检测显示等措施，使玻纤袋式除尘设备在立窑、烘干机除尘中能_、稳定运行，烟囱出口排放浓度低于_规定的150gm/m3排放标准，实际可_不大于50gm/m3。
　　Fiberglass bag type collector our production is designed for vertical cement kiln waste gas dedusting and dryer developed high-quality equipment, this equipment adopts microcomputer control, sectional reverse blow, timing, constant resistance dust, temperature detection and display of such measures, the fiberglass bag type dust removal equipment in shaft kiln, the drying machine in addition to high efficiency, stability operation of dust, the outlet of chimney emission concentration lower than the state 150gm/m3 emission standards, the actual can guarantee that not more than 50gm/m3.
　　该设备可不停机分室换袋，操作简单，安全可靠，运行费用低，是解决立窑、烘干机废气除尘的有效设备。袋式除尘设备的工作原理：由于立窑、烘干机废气具有含灰浓度高、风量大、污染范围广、湿含量高等特点。给烘干机、立窑烟气的除尘带来了_的困难，根据烘干机、立窑的特点，采用上进气方式，含尘烟气由上部进入进气室，部分粗颗粒由于惯性落入灰斗，清灰时因气流方向与粉尘沉降方向一致，防止了粉尘的二次飞扬。
　　The equipment is not stopping points room change bag, simple operation, safety and reliability, low operating cost, is an effective solution to the shaft kiln, drying machine waste gas dedusting. The working principle of the bag type dust collecting equipment: because the shaft kiln, drying machine with high concentration of waste gas containing dust, air pollution, wide range, high moisture content. It brings a lot of difficulties, kiln gas dust drying machine, drying machine, according to the characteristics of shaft kiln, the gas, dust containing gas into the chamber from the upper portion of coarse particles due to inertia, falling into the ash bucket, ash and dust deposition due to the airflow direction is consistent with the direction, to prevent the two flying dust.
　　袋式除尘设备的结构特点：袋式除尘器的基本结构由3个部分组成，玻纤袋式除尘设备的进气、排气及反吹系统：包括进气管道、进气室、反吹阀、反吹风管、三通管、排气阀、排气管。袋室结构：包括灰斗、检修门、本体框架、上下花板、滤袋、袋室。排灰系统：包括排灰阀、螺旋输送机。玻纤袋式除尘器本体为全钢结构，外壳采用轻质岩棉板保温，保温厚度为100mm，外壳用δ 为0.5mm 镀锌板保护。
　　The structure characteristics of the bag type dust collecting equipment: the basic structure of bag type dust collector is composed of 3 parts, fiberglass bag type dust collecting equipment inlet, exhaust and reverse blowing system: including the inlet pipe, an air inlet chamber, reverse blow valve, anti blowing pipe, three way pipe, the exhaust valve, exhaust pipe. Bag: chamber structure comprises an access door, frame, body, upper and lower plate, filter bag, the bag room. The ash system: including the ash valve, screw conveyor. Ontology fiberglass bag type collector for the whole steel structure, the shell adopts light rock wool insulation, the insulation thickness is 100mm, shell with δ 0.5mm galvanized sheet protection。